ViStar Satellite TV Boxes

1. Press MENU
2. Select SYSTEM CONFIGURATION, press OK
3. Enter PASSWORD (Default is 1234)
4. Select FACTORY DEFAULT, press OK
5. Enter PASSWORD (Default is 1234) “Do you want to reset to receiver?”, The access code reset to default?”
6. Press OK (wait for about 5 to 10 seconds)
7. Will Display WELCOME: press OK to continue
8. Will Display LNB CONFIGURATION: check specifications as follows:

ANTENNA :1

SATELLITE :Default 01

LNB TYPE :Universal

LNB POWER :Yes

LNB LOW FREQ. (kHz) : 9750000

LNB HIGH FREQ. (kHz) : 10600000

DISEqC / TONE BURST : Disable

9. Press OK

10. Will display ADD CHANNELS; check specifications as follows: (Signal Strength about 50%; Signal Quality above 75%)

SATELLITE : Default

TRANSPONDER : TP1

FREQ. (kHz) : 12661000

SYMBOL RATE : 26042 kS/s

0 / 22 kHz : ON

POLARIZATION : 18V

SEARCH TYPE : Network

11. Press OK (SEARCH CHANNEL) “Searching In Process, Please Wait...”

12. Will display (52) Digital TV Channels; (11) Radio Channels

13. Press OK to complete the procedure.

NOKIA Satellite TV Decoder

1. On your Remote Control, select MENU
2. Select SETTINGS by pressing the left arrow button
3. Press the up arrow button to SYSTEM CONFIGURATION, press OK
4. Enter your ACCESS CODE (Default 1234)

5. Under CHANNEL SEARCH, select MANUAL SEARCH
6. Set the following configurations:

Transponder Frequency : 12.661

Polarization : H (Horizontal)

Symbol Rate : 26042

FEC : AUTO

Network Search : NO

7. Be sure to have signal before pressing OK
8. Will display all the Channels searched, press OK
9. Press BACK to exit the installation
10. End of procedure.

Hyunda-Crystal boxes

1. Press MENU
2. Under INSTALLATION, select TP EDIT / SCAN, press OK
3. Edit or set the configurations as follows:

Satellite Name AGILA 2

TP Frequency 12.661 Ghz

Polarization Horizontal 18V

Symbol Rate 26.042 MSPS

Scan Free Scrambled

TP Delete -----

4. Press OK
5. Will display all the CHANNEL SCANNED
6. Exit the installation to view new channels.

HOMECAST Digital Satellite TV Decoder

1. Press MENU, OK
2. INSTALLATION, OK
3. Select MANUAL SEARCH
4. Enter the ACCESS CODE (Default 1234)
5. Set the configurations as follows:

Frequency : 12661 MHz

Polarity : Horizontal

Symbol Rate : 26042 ks/s

Code Rate : 3/4

Scan Mode : Free+CAS

Service Type : TV+Radio

Network Search : Enable

PID Search : Auto PID

6. Press OK
7. Will display “Do you want to save changes?”, select YES
8. Exit the installation to view new channels.

Digit-All-World (DAW-951) Decoder

1. On your remote control, press MENU
2. Go to INSTALLATION, select CHANNEL SEARCH then press OK
3. Enter ACCESS CODE (Default 1234)
4. Under EQUIPMENT, select NONE, press OK
5. CHANNEL SEARCH, select MANUAL (GREEN button)
6. Select ADD TP to set configurations
7. Will display the ADD TP, then set the new TP # specifications as follows:

TP # :5

Freq :12661MHz

S/R : 26042 ks/s

POL : H

FEC : AUTO

VPID : AUTO

APID : AUTO

PPID : AUTO

NIT :OFF

8. Select the new TP #, press SUB. T button, press OK
9. Confirmation, “SAVED” will appear, press OK
10. Exit the installation to view new channels.